• Baron23
    11.9k
    For sale is my NewVape Micro-20 Rosin Press.

    Micro-20 originally sold for about $3,500 before shipping

    $1,250 $1,000 $750 will take it but it must be purchased face to face as there is no way to box and ship its…it’s that heavy duty. I live in Maryland.

    I will consider reasonable offers also.

    YES, STEAL IT FROM ME, PLEASE! :-)

    I’ll accept cash, PayPal FF (or you pay the fee), or a cashier’s check in payment.
    I’m selling it because I just don’t use it. I’m 95% flower user and I live in a med legal state so if I want concentrates I just buy them.

    Also, I need the room on my bench for metallic cartridge reloading! Haha

    The Micro-20 is a semi-commercial production quality press. And this has not been used very much at all and is almost brand new

    The plates are 4” x 7” and it’s driven by BVA hydraulics which are warrantied for life and are the gold standard for this level of pumps/cylinders indeed a 20 ton press.

    How that 20 ton is calculated is from this formula:
    (PSI from Gauge x Jack cylinder area) / area of load = PSI on the Puck

    Where jack cylinder area is 4.37 square inches in this case

    So, it’s a 10K psi pump but you really shouldn’t go to a pumps maximum, or at least not often.
    So, take approximately 90% = 9,153K PSI on the pump x 4.37 jack cylinder area = 39,998 lbs. of force on the plates = 20 tons…within a few lbs.

    Then take the total force exerted on the plate and divided it by the area of your puck in square inches and you get actual PSI on your material. For example:

    2,000 psi on the gauge x 4.37 = 8,740 total force on the plate divided by a 4 for a four square inch puck = 2,185 PSI on your material.

    Here is my set up: Micro-20 press, gauged BVA pump and cylinder, two double PID controllers.
    kyu6l6nmyv22lgus.jpeg
    w0f2qn8xquzej4ib.jpg

    Note the curved ends of the side bars which let you roll the press over and do drip tech.
    d9n45vh9tqjvbc5m.jpg

    The only “damage” is a small bit of the hydro cylinder paint was scratched off during shipping (I believe) by the frame of the unit. It’s been this way since delivered and has not rusted nor in any way caused any issues. If you wish, you could take a small paint brush and paint over it….but I wouldn’t bother, personally.
    htqnmk00fmzaeuyq.jpg

    Now, compare this to the current NV 20 Ton BVA press (shown below) that sells for $3,650. Note that the Micro-20 did not need springs and guide rods because the frame itself is that strong and rigid.
    https://www.newvape.com/collections/rosin-press/products/bva-20-ton-large-frame-rosin-press
    z57pl9twlhwwg7ke.jpg

    But wait, if you buy the Popeil….err, NV Micro-20 (LOL) in the next 10 minutes, you will also get round and rectangular puck pre-presses molds!
    m0etggst4wlj1uwy.jpg

    But there is MORE!!
    You will also get a cooling plate and high temp thermometer
    kx13t9ts5l2qas4k.jpg

    But don’t go away….we are giving away EVERYTHING
    Buy the Micro-20 and for absolutely free, I’ll throw in 55 lbs. parchment paper, Slick Paper, and 160, 120, and 90 micron bags AND the silly tool I bought to turn them inside out so the seam is inside (which surprisingly hard to do PIA by hand on small bags)
    mkk556lcjt537zww.jpg
    cdgwmqfgykm3fp0x.jpg

    PM me with any questions you may have.

    Thank you for looking at this advertisement.
    Attachments
    IMG_0797 (60K)
    IMG_0800 (69K)
bold
italic
underline
strike
code
quote
ulist
image
url
mention
reveal
youtube
tweet